Fast Fit® Continuous Bench End Kit 2 — 4ft

Fast Fit® Continuous Bench End Kit 2 — Modular Bench Component for Customisable Growing Bench Systems (4ft)

Key Features & Benefits

• Modular Continuous Benching System (8-24 ft Configurable): The Fast Fit® Continuous Benching System allows growers to build a bench line anywhere from 8 to 24 feet in length by combining End Kits, Middle Kits, and Component Supplements. The system is designed to scale with your growing operation, allowing you to start small and expand your bench infrastructure as your facility grows.
• Role of the End Kit 2: End Kits form the terminating sections at each end of a Fast Fit® Continuous Bench run, providing the structural end frame and leg assembly that anchors and caps the bench at its starting and finishing points.
• Minimal Tools Required — Fast Assembly: Fast Fit®’s patented no-hassle design minimises tool requirements and assembly complexity. Growers can configure and deploy continuous bench sections quickly, reducing facility setup time and getting growing surfaces operational faster.
• Compatible with Botanicare® CT Trays.
• Designed Specifically for Fast Fit® Continuous Benching: Every component — End Kits, Middle Kits, and Component Supplements — is engineered to interface precisely with other Fast Fit® Continuous Bench components, ensuring structural integrity, consistent tray height, and reliable performance across the full bench configuration.
• 4ft Width Format: This End Kit 2 is sized for 4ft bench configurations, matching the corresponding Fast Fit® Continuous Bench infrastructure for correctly dimensioned bench runs in grow rooms and greenhouse environments.

Who Should Use This

Fast Fit® Continuous Bench End Kit 2 (4ft) is designed for indoor growers, greenhouse operators, and commercial cultivation facility managers who are building or expanding a Fast Fit® Continuous Benching System. It is the correct component for growers who need to add, replace, or extend sections of an existing Fast Fit® continuous bench run, or who are configuring a new bench system from scratch in a grow room or greenhouse environment.

Compatibility

Designed for use exclusively with Fast Fit® Continuous Benching System components. Compatible with Botanicare® CT Trays. All Fast Fit® Continuous Bench kits — End Kits, Middle Kits, and Component Supplements — are engineered to work together as a unified system. Mixing components from other bench systems or manufacturers is not recommended and may compromise structural integrity or tray fit.

Frequently Asked Questions

What is the difference between End Kit 1, End Kit 2, Middle Kit 1, and Middle Kit 2?

Fast Fit® Continuous Benching offers multiple kit configurations to support different bench layout requirements and structural needs. End Kits (1 and 2) form the terminal ends of a bench run, while Middle Kits (1 and 2) provide intermediate support and extension sections. The numerical designations (1 and 2) correspond to different structural configurations within each kit category. Consult the Fast Fit® Continuous Benching System guide or your Hydrofarm distributor to determine the correct kit combination for your specific bench length and layout.

How long can a Fast Fit® Continuous Bench be configured?

The Fast Fit® Continuous Benching System supports bench runs from 8 to 24 feet in length by combining the appropriate number of End Kits and Middle Kits. As your growing operation expands, additional Middle Kits can be added to extend an existing bench run within the supported length range.

Can I mix 4ft and 5ft components in the same bench run?

No. Fast Fit® Continuous Bench components are sized to match specific bench widths — 4ft or 5ft — and should not be mixed within the same bench run. All components in a single bench configuration must be the same width to ensure proper structural alignment and tray seating.

Are Botanicare® CT Trays included with this kit?

No. This listing is for the Fast Fit® Continuous Bench End Kit 2 (4ft) only. Botanicare® CT Trays are sold separately. Confirm tray compatibility with your specific Fast Fit® bench configuration before purchasing trays.

What tools are required for assembly?

The Fast Fit® Continuous Benching System is designed for minimal tool assembly. While some components may require basic hand tools for certain fastening steps, the patented no-hassle design minimises tool requirements significantly compared to conventional bench assembly systems. Refer to the included assembly guide for the specific tool requirements for your kit.